2012年02月25日
面HOP動画
ORGA 面HOP動画
ORGAです★最近Blogの更新が少なくてすいません><
いつもの事ながら、バタバタとなっておりまして、メールの返信も遅れてしまっておりますTOT
今晩~明日に掛けて集中でメールの方対応して参りますので、もう暫くお待ちください。
さて、今日は、ORGA Overseas向けではありますが、FireFly なまず辛口 を利用したHop Install videoを作成してみました。
こんな感じのコンテンツは今後、どんどんUPしていきますので、楽しみにしててください。
ちなみに、今回のVideoはOverSeas向けとなりますので、全部英語です。
後に 日本語版もUPしますので、楽しみにしててください。
念のため、以下に文章を記載します。
To install the Namazu Flat Hop you will need:
- your disassembled hop-up unit
- an ORGA Magnus 6.23mm WideBore Barrel
- Namazu Flat Hop nub
- hop bucking
You will also need:
- a Small pair of scissors
- an exacto knife
- crazy glue
We will start by placing the Magnus barrel in the hop unit, using the retention C-clip to hold it in place.
Check the hop-up window to make sure it is aligned. Notice that the inner barrel can be seen slightly towards the back of the hop window. We want to make sure that the Namazu doesn't pinch in this area, so we will cut the Namazu down to size.
We are going to want to cut off the two protruding sections, as these can flex when excessive hop is applied, and may pinch in the hop window, preventing the hop from being turned down or off. Use the size of the hop window as a guide when judging how much of the Namazu to cut.
First step is to snip off the two protruding points of the Namazu with your scissors so that is looks similar to this. Then use your cutting knife to remove the excess hop rubber from the back of the Namzu. Your cut should look like this.
Then place the small steel pin into the hole in the center of the Namazu. This helps to prevent side to side movement and helps keep the hop stable. It will also keep the hop rubber from compressing in the center when applying large amounts of hop.
Confirm that the extruding section of the Namazu is at the front. This should be on the opposite side of the hop window, away from any exposed inner barrel.
Next, use a couple small dabs of crazy glue to keep the Namazu securely in place. This helps to prevent hop rubber movement when the hop is applied.
When placing the Namazu in the hop arm, make sure to angle it slightly up. This will ensure that the hop is applied flat when you install it back into the hop unit. If you install the Namazu flat, then it will have a slight downward angle when placed in the hop unit, and hop won't be applied evenly when used.
Reinstall your barrel, making sure to rotate the hop bucking so that the internal grove is off center, leaving a smooth area for the flat hop. If you don't have a Magnus barrel you will need to invert your hop bucking and file down the inner hop ridges.
Confirm your hop is working and install the rest of the hop unit.
【入荷情報】IRON AIRSOFT MWSガスブロ用トリガーユニット、DEAD AIR SANDMAN-Sサイレンサー
【入荷情報】電動ガン用バッファチューブ2種、メインスプリング、M4用グリップ 新入荷!
【入荷情報】SOTAC GEAR製 ウェポンライト 11種類 新入荷!
【入荷情報】FCC PMAGトレポン用、フルシリンダー、チャージングハンドル他、再入荷!
【入荷情報】SOTAC GEAR製 MODLITE タイプ PLHV2ウェポンライト 新入荷!
【入荷情報】IRON AIRSOFT LANTAC Dragon KEYMO Wolfmanタイプ マズルブレーキ他
【入荷情報】Killer Innovations VELOCITY V1 COMP SIG P320 ガスハンドガン
【予約受付開始】EMG X T8 DANIEL DEFENSE DDM4A1 RIII ガスブローバック
【入荷情報】IRON AIRSOFT MWS用レシーバー他、EMG×T8 Mk18 RIII ガスブロ 予約受付開始!
【入荷情報】BJ TAC B5 SYSTEMS TYPE 23 タイプ グリップ ガスブロ用、PTWチャンバー用シム他
【入荷情報】電動ガン用バッファチューブ2種、メインスプリング、M4用グリップ 新入荷!
【入荷情報】SOTAC GEAR製 ウェポンライト 11種類 新入荷!
【入荷情報】FCC PMAGトレポン用、フルシリンダー、チャージングハンドル他、再入荷!
【入荷情報】SOTAC GEAR製 MODLITE タイプ PLHV2ウェポンライト 新入荷!
【入荷情報】IRON AIRSOFT LANTAC Dragon KEYMO Wolfmanタイプ マズルブレーキ他
【入荷情報】Killer Innovations VELOCITY V1 COMP SIG P320 ガスハンドガン
【予約受付開始】EMG X T8 DANIEL DEFENSE DDM4A1 RIII ガスブローバック
【入荷情報】IRON AIRSOFT MWS用レシーバー他、EMG×T8 Mk18 RIII ガスブロ 予約受付開始!
【入荷情報】BJ TAC B5 SYSTEMS TYPE 23 タイプ グリップ ガスブロ用、PTWチャンバー用シム他
※このブログではブログの持ち主が承認した後、コメントが反映される設定です。